Recently, affected by the revision of Japanese laws, Amazon Japan has frequently issued announcements, reminding sellers that products exported to Japan should be adjusted, and seat belt sellers should pay special attention! Xing Gong: 18062610065

In addition, after this revision, only "Human Belt Type" (single suspension) and "Horse Belt Type" (single suspension) will be recognized as "Fall Protection Equipment" because these devices will meet the revised structural standards. It is important to note that due to the end of the transition period, after January 2, 2022, fall arrest equipment that does not meet the revised structural standards has been banned from sale.

The policy for carabiner sold on Amazon in Japan requires: /ASSE Z359.12-2009, ASTM F1774 or UIAA 121 certification report for carabiner, the report requires a warning slogan, packaging image, product image

Fall Prevention Equipment Standards

(January 25, 1991) (Ministry of Health, Labour and Welfare Notice No. 11)

With the implementation of the Cabinet Order (Internal Decree No. 184 of 1991) partially amending the Regulations for the Implementation of the Industrial Safety and Health Act, the Industrial Safety and Health Act (Act No. 57 of 1947) No. 4 is based on Article 12 of the following provisions, So Google Translate No. 38) will be modified as follows, and from

Applicable from February 1, 001.

Fall Prevention Equipment Standard (Definition)

In this notice, the terms listed in the following items have the same meaning as each item.

(1) A person wearing a fall arrester with a full harness (hereinafter referred to as the "wearer") acts on the shoulders, waist and waist with the load applied to the body when the fall is stopped. Thigh It refers to the instrument that has the structure to support it.peach

(ii) Ribbon-like devices for torso straps attached to the waist of the body.

(i) Attach the lanyard full harness or torso strap to the main warp or other installation equipment (means the equipment used for the safe installation of fall arrest equipment; the following paragraphs of this article and the following paragraph 3 apply). Cables or straps (hereinafter referred to as "lanyards, etc."), connectors, etc. (iv) Connectors are devices used to connect the complete set of seat belts, lap belts, lanyards, mounting equipment, etc. to each other. (Y) A shock absorber is a device used to reduce the shock generated when a collision is stopped. (6) Winding machine A device that uses dry winding and hanging knitting, etc.

The second anti-collision equipment used at a height of 6.75 meters or more should be a full wire harness type.

2) The fall prevention equipment must be able to withstand the total weight of the wearer of the fall prevention equipment and the mass of the equipment. The lanyard must be based on the height of the work area and the installation of the equipment. (put up)

The third full-wire harness type fall arrest equipment (hereinafter referred to as "full wire harness type fall arrest equipment") must meet the following standards.

(1) When the collision is stopped, the load applied to the wearer's body acts on the shoulders, waist and waist. The thigh structure should be properly supported by the full seat belt. The complete set of seat belts should be able to fit the wearer.

(3) The lanyard (including the shock absorber) should be properly connected.

(4) The buckle should be able to connect positively, and the connecting part is not easy to be disengaged.

The torso belt type fall arrest device (hereinafter referred to as the "belt type fall arrest device") must meet the following standards. () The structure shall support the body load imposed by the torso belt on the torso of the wearer in the event of a crash. (ii) The torso harness shall be able to fit the wearer. (3) The lanyard is connected to the positive sulphur. (part strength)

Article 4 The parts and components of the anti-fall equipment shall be of the categories listed in the upper column of the table and have the strength specified in the lower column of the same table.

Category Power

The entire harness passes the tensile test method specified in Japanese Industrial Standard T8165 (fall arrest device) or equivalent method when a tensile load of 150 kN is applied to the trunk head and rugged trunk foot. Apply a tensile load of 100 kN in the direction of the part.

The torso strap will not break when a tensile load of 150 kN is applied using the tensile test method specified in Japanese Industrial Standard T8165 (Fall Protection Equipment) or equivalent.

22.0 kN for braided belts or fiber ropes such as lanyards, 15 for steel wire ropes or chains, and the tensile test method specified in Japanese Industrial Standard T8165 (fall prevention equipment) or the equivalent method. It does not break when a tensile load in kilonewtons is applied. However, for braided tapes or fiber ropes used in combination with shock absorbers, the tensile load may be 150 kN in accordance with the criteria specified in the first category in the table of Article 8, paragraph 3. …

Connector (1) When a tensile load of 11.5 kN is applied using the tensile test method specified in Japanese Industrial Standard 8165 (fall prevention equipment) or an equivalent method, the product breaks and loses its function. Loss of functionality of the fixture.

(1)) When tested in accordance with the test method specified in Japanese Industrial Standard 8165 (fall arrester) or an equivalent method, it will break, deform to such an extent that it loses its function, or prevent it from falling off. Do not lose the functionality of the device.

Japanese station seat belt/climbing standard JIS T8165 standard processing process: