ErP certification is a certification requirement based on the ErP directive under the EU CE mark, and the ErP directive is a new European CE mark regulation. As a CE mark directive, the ErP directive is now required to be combined with the LVD directive, EMC directive, RoHS directive, etc. requirements are executed together. Therefore, before the products involved in the relevant implementation measures are exported to Europe, the requirements of the ErP Directive must be considered before they can be affixed with the CE mark. Why is energy efficiency important? For most people, 50-60% of our energy bills come from heating, and the more efficient your boiler is, the cheaper your energy bill will be. Plus, when a boiler wastes fuel, it puts it into our atmosphere as carbon. If you replace an 88% efficient boiler with a 91% model, you won't see a particularly noticeable reduction in your bill, but replacing an older G-class boiler with a modern heating system can save you a lot.
The scope of ERP testing includes: 1. ERP certification requirements for energy-saving lamps: NO.244 2. ERP certification requirements for products and IT products: .1275 3. ERP certification requirements for TV products: NO.642 4. ERP certification requirements for set-top boxes: N.107 5. ERP certification requirements for ballasts and fluorescent lamps: NO.245 6. ERP certification requirements for external power supplies, adapters, and chargers: N.278 ErP mainly considers the life of lighting products, light color and electrical parameters, The main tests are as follows: 1. The distributed photometer test measures the light distribution curve to confirm whether it is a directional light or a non-directional light by accumulating the luminous flux 2. Switch test The switch cycle is 15,000 times, on for 3 seconds and off for 3 seconds. The failure rate cannot be higher than 5%. 3. Integrating sphere test 1) Start-up time is less than 0.5s 2) Warm light time is less than 2s 3) Color rendering index (CRI) is greater than 80, outdoor or industrial use is greater than 65 4) Color consistency: the color tolerance in elliptical coordinates is less than 6 5) Power Factor: P≤2 W: no requirement ? 2 W < P≤5 W: PF > 0,4 ? 5 W < P≤25 W: PF > 0,5 ? P > 25 W : PF > 0,9 4. Aging test This test mainly considers the comparison between the initial light parameters of the lamp and the light parameters after a certain period of time aging test. The main parameter is the lumen maintenance rate. Starting from September 1, 2013, the lamps must be aged for 1000 hours (continuously turned on). From September 1, 2014, it must undergo 6,000 hours of aging. The failure rate cannot exceed 10%, and the maintenance rate should be greater than 80%. How to effectively do ERP certification: product conformity in accordance with the internal design control procedures in Annex IV of the /EC Decree. A simple and effective method of compliance is to refer to Annex IV of the EuP Decree, namely: 1. Provide the LCA (Life Cycle Assessment) environmental footprint report of the product 2. Provide the test report required in the Eco-design Implementation Rules 3. Provide the required information but The effective method is an internal control ERP certification process: 1. Compliance · According to the requirements of the ERP Directive, manufacturers can implement two types of “internal design control” (Annex IV of the ERP Directive) or “Environmental Management System” (Annex V of the CRP Directive). Select one of the evaluation modes to evaluate. 2. Organize and form technical documents (TDF) Manufacturers must form technical documents Technical documents should include information on design, manufacture, operation and final disposal of products. doc) ·Basic information to follow the instructions and standards 4. Labeling CE mark ·Coordinated standard testing-EMC, LVD, etc. ·Labeling CE mark ERP certification cycle is usually 2-3 weeks, can be expedited, expedited need to pay extra.
Shenzhen Huapin Testing Technology Co., Ltd. adheres to the principles of science, accuracy and rigor, and relies on excellent testing equipment and experienced testing and certification. Testing and certification consulting services provided to tens of thousands of enterprises. For details, please contact: 13428693948